We handle metal roof coating in Highview, starting with a check of which side of the Jeffersontown line the building sits on, since that decides who reviews the work.
Many Highview buildings carry a Louisville mailing address while sitting a short drive from Jeffersontown. Highview is a Louisville Metro neighborhood, so Jeffersontown's permitting department and its HVAC inspector have no role there.
We confirm the parcel's jurisdiction in Metro's property records before any permit question. Then we list the scope plainly, keeping a coating with screw replacement apart from panel or curb changes.
A clear scope makes the Metro review simple. These five items are listed one by one.
Screw testing, tightening, and replacement on exposed-fastener roofs, counted by roof area. It is part of a coating job and listed as its own line.
Side laps, end laps, and opened seams sealed with mastic or reinforced tape. The lengths go on the scope so the reviewer sees the full extent.
Panels with holes or rust-through replaced before coating. Listing them separately shows the reviewer this goes beyond a coating.
Curb flashing repairs, and any unit that comes off its curb. In Highview, Louisville Metro's HVAC inspection applies when a unit is disconnected and reset.
The coating system, its thickness, and the products used, with wet film readings. These, plus the permit number, go into the roof file.
For a smaller Highview commercial building, a coating keeps the job simple as well as the roof dry.
A coating with screw replacement is a smaller scope than replacing panels or altering curbs, which keeps the Metro paperwork lighter and the job shorter. The existing roof stays in place under the coating.
Primed and coated laps and screw heads rust more slowly than bare steel on older buildings.
Work stays on the roof, so a small shop or office keeps serving customers.
Coating over the old roof sends far less material to the dump than a tear-off.
Highview's smaller commercial buildings usually land on one of these three systems.
Exposed-fastener roofs with solid panels get screw and lap work, rust primer, and a field coat.
Metal roof coating
Heated shops and offices that need insulation get foam over the panels, then a protective coat.
Spray foam roofing
Low-slope sections that hold water get silicone after seams and drains are sealed.
Silicone roof coatingCall us with the property address. We will help sort out jurisdiction and what the scope needs to list.
Paperwork and roof work move in this order.
We walk the roof, test screws, check laps and curbs, and confirm the parcel's jurisdiction in Metro property records before any permit question.
Coating, screws, laps, panels, and curb work are listed as separate items for Louisville Metro's small commercial process.
Applications go through Metro's online Accela portal, and the permit number is kept with the roof records.
The roof is washed, repaired, primed, and coated, with wet film readings and product names added to the file.
Highview is one of six areas where we coat commercial roofs. For a building outside these towns, call us or send us a message.
Mansard bottom edges and rear screw rows.
City Letter of Compliance before office roof work.
Zoning step before a street-facing color is picked.
Gutters resealed while downspouts stay where they are.
Answers about the Metro process, jurisdiction, and roof records in Highview.
Smaller commercial buildings there do, since Highview is a Metro neighborhood with no city government of its own. Metro's Construction Review keeps a Small Commercial Project page describing what smaller jobs submit. Have the building use, square footage, roof area, and a work description ready, and file through Accela.
List each item on its own line: coating system and area, screw replacement, lap and seam sealing, any panel replacement, and any curb or unit work. A coating with screw replacement reads as a smaller job than one that also replaces panels, so the separate lines help the reviewer.
No. Highview sits outside Jeffersontown city limits, so the city's permitting department and its commercial HVAC inspector have no role there, and Louisville Metro handles building permits and HVAC inspection. Mailing addresses near the line can mislead, since many properties carry a Louisville address close to Jeffersontown.
Look the address up in Louisville Metro's property records, which show whether the parcel falls inside a small city like Jeffersontown or in a Metro neighborhood like Highview. If the record leaves any doubt, call Metro's permit office with the parcel number before applying.
Louisville Metro's HVAC inspection applies in Highview when a unit is disconnected and reset for curb flashing repair. A short drive away in Jeffersontown, the city's own inspector handles the same work. The coating crew preps and seals around the curb, and a mechanical contractor handles the unit.
Keep the permit number, the coating product names and colors, the primer used, wet film readings by area, and dated photos of the finished details. That file answers the first questions at the next recoat or repair, especially which products can go over silicone.
Enter the roof size for a ballpark range, or call with the property address to get started.
Leave a name and number and we will call you back about your commercial roof.
Or call us now: (502) 293-5577